Stoelting E257 Uživatelský manuál

Model E157/E257/F257Owner's ManualManual No. 513563 Jul. 2003, Rev. 2

2Figure 1Model E157 - FrontFigure 3Model E257/F257 - FrontFigure 2Model E157 - SideFigure 4Model E257/F257 - SideNOTE: Figures in parenthesis are in c

32.1 SAFETY PRECAUTIONSDo not attempt to operate the freezer until the safetyprecautions and operating instructions in this manual areread and complet

4Figure 6Warning Label Locations - E157IMPORTANT NOTICE TO OPERATORBEFORE INSTALLING EQUIPMENT, READ THE OWNER'S MANUAL CAREFULLY. TAKE NOTE OF A

5Figure 7Warning Label Locations - E257/F257IMPORTANT NOTICE TO OPERATORBEFORE INSTALLING EQUIPMENT, READ THE OWNER'S MANUAL CAREFULLY. TAKE NOTE

6D. The floor model freezers are equipped with air-cooledcondensers and require correct ventilation. The front ofthe freezer is the air intake and mus

72.4 ADJUSTING CUP DISPENSERSTo adjust the cup dispensers, install the size cup desiredinto the dispenser and turn the wing nuts on the dispensermount

8

9SECTION 3INITIAL SET-UP AND OPERATION3.1 OPERATOR'S SAFETY PRECAUTIONSA. Know the freezer. Read and understand the OperatingInstructions.B. Not

10A. STIRRING ONLY-OFF-STIRRING & FREEZINGSWITCHThe STIRRING ONLY-OFF-STIRRING & FREEZ-ING switch is a three-position toggle switch used toco

11Inspection for worn or broken parts should be made duringevery disassembly of the freezer for cleaning or otherpurposes. All worn or broken parts s

12Figure 15Removing Spigot AssemblyFigure 16Removing Spigot O-Ring from Spigot bodyÈÈFigure 17Cut-away View of Spigot AssemblyKNOB#482024O-RING#624607

131. With a clean, dry towel, wipe excess lubricant from thespigot assembly and o-ring. Firmly grasp the spigotassembly with both hands and squeeze th

14Figure 21Removing Divider Plate from Agitator Fingers6. Remove the drive shaft by pulling straight up andout of the vertical center post (Fig.22).Fi

153.5 SANITIZING THE FREEZER AND FREEZERPARTSAfter the freezer parts have been soaked and washed inwarm, soapy water, they should be rinsed thoroughly

16 2. Install the drive shaft into the center post byrotating and pressing down lightly on the shaft untilthe shaft drops down and engages with the g

17B. Assemble O-rings onto the spigot plungerswithout lubricant. Then apply a thin film ofsanitary lubricant to the exposed surfaces of theO-rings.1.

18A. DAILY1. The exterior should be kept clean at all times topreserve the lustre of the stainless steel. A mildalkaline cleanser is recommended. Us

19Figure 28External Parts To Be CleanedCUP DISPENSERS AND LIDSLIQUID LEVEL INDICATOR DRIP TRAY SUPPORT, DRIPTRAY, DRIP TRAY GRIDALL PANELSCOVERSFLAVOR

20

214.1 HOW TO ORDER DECALS AND TAGSTo assure receipt of the proper warning decals, supply your dealer or distributor with the following information:A.

Need Parts or Service?We stock the parts you need.Our Technicians are factorytrained and are certified in theStoelting Technicare program.Model No.:

22Model E157 Exploded View4.2 Explosed Views and Parts Lists

23Model E157 Parts List

24Model E257 Exploded View

25Model E257 Parts List

26Model F257 Exploded View

27Model F257 Parts List

28

29ADDENDUMFILL-O-MATICThe Fill-O-Matic is a transfer pump designed to keep thefreezer full of product.A. Pump Hose RemovalWARNINGDISCONNECT THE FREEZE

30

WARRANTYMIX TRANSFER PUMPS / COCKTAIL / SLUSH1. Scope: Stoelting LLC warrants to the first user (the “Buyer”) that the evaporator assembly and co

OWNER'S MANUALMODELS E157/E257/F257SLUSH FREEZERSThis manual provides basic information about the freezer and its components. Instructions andsug

TABLE OF CONTENTSSECTION 1 - INTRODUCTION ... 11.1 Descriptio

LIST OF ILLUSTRATIONSFigure Title Page1 Model E157 - Front.......

11.1 DESCRIPTIONModels E157/E257F257 freezers are gravity fed. Thefreezers are equipped with fully automatic controls toprovide a uniform product. The